temper

Aluminum wheels help with less roll over.

I just got my Temper a week or so ago. I'm not that new to RC, but this is my first crawler. The first thing I did was remove the foams entirely from all four tires. This made a decent difference in the capabilities. The mod with the biggest difference was switching the servo from the...

Not turning up anything on the Internet for a bearing upgrade for the 1/24 Temper. Has anyone here replaced the stock bronze bushings with bearings? If so, did you make note of the sizes? Otherwise I suppose I'll just have to warm up the calipers and do it myself! :)

Found a local group of crawlers and meet up with them.

So I finally got around to spending a little money on the Temper. I bought a Venom 200mah 2s Lipo battery and a Venom Pr2 charger. While I was there I also picked up a set of Pro-Line Interco TSL 1.9 tires because the guy said they would fit the factory rims......... they don't. Has anyone...

Hi Tempers, Would be nice to post your Temper pictures in one dedicated thread. Starting:

Just got my Temper from Amazon yesterday. First off the steering dual rate on the tx was set real low from the factory, and harm cranking it up to 10? The truck had the throttle reversed also from the factory, but changing it to reverse fixed that. Last I noticed almost all the suspension...

The only question I have for y’all is about motor behavior: does yours make that kinda shhhh-shhhh-shhhh-shhhh-shhhh-shhhh noise while moving forward? Very hard to describe it with words, but almost sounds like a stuttering. It runs fine, but the sound is definitely not smooth when compared to...

Hey guys, just purchased an ECX Temper this past Friday and have been tinkering around with it. Driftomatics video's helped me out a bit (subbed you Drifto). So far have done some of the easy mods until I get paid again this week, then it's on for some major mods... So far, I switched the...

I recently upgraded my temper to 1.9 axial wheels and tires and they rub pretty bad I was wondering what kind and where did you guys get yours

ok here I was called out about how cheep I did my 4ws without using a signal reverser I'll post pics in the rear I'm using a hexfly Hx-3cp servo which turns opposit from the hitec hs-625mg so when mounted when the front turns right the rears go left making it go right and I used a y-cable. Then...

ok so I decided to get just a little wild with my TEMPER I'm going to be removing the brushed motor and go brushless 4800 kv going to try with stock pinion stock spur for testing then I'm going to try and find some bigger pinion gear I'm also will be running Traxxas gravedigger style tires I'll...

I just got an ECX temper. I plan to mod it significantly. However, since I don't have lots of money it will be a long journey. That said, I have already made several changes. I reversed the battery tray and I put the ESC on the bottom of the battery tray. I plan to get bigger better tires and...

Has anybody attempted to stretch their 1/18 temper? I'm looking at it and if I can get about 1/2 at each axle it will really open up options for different bodies. The driveshafts definitely have plenty of travel to them. Ia total of 1 inch on these is alot but even an 1/8 at each end would help.

Check out this 1/24th scale ECX Temper crawler, looks pretty capable for such a small RC.

Hi everyone, new to the rc world here. How do you remove the foam from the tires? Thanks in advance for the help!

Hey all this is my first crawler I come from boats and short course trucks and I absolutely love this thing. All stock other than axial bead locks with 1.9 TSL's. Went to change shock fluid the other day and noticed one of them has a bent piston, should I go stock or are there any upgrade shocks...

Just ordered a tazor 280 for the rc. Was wondering who's had experience with this motor? What's the gains and what is the install like?