boost

Anyone know what size screws are used for the front bumper on boost? I lost mine. I tried a m3 so I think it that width just need to find a shorter one, much shorter.

A bit ago, I lost 2 shoulder screws. I noticed my steering knuckle had horribbllleee threads just now and I found a Hot racing Steering block upgrade. Will this eliminate that issue somewhat? I understand that I should add some thread lock to it, would silicone glue or any other glue work or...

Hello, just seeing if anyone would know the answer to this question. Would a hobbystar 35a esc/120a burst be sufficient in the boost with the skyrc toro 2800kv motor? That motor claims the "max current" to be only 33a, this kind of confused me as its a 540 motor and I've even seen cheaper ones...

My Boost chassis snapped in two as well as my center steering link. I’m looking to replace the chassis by making an Aluminum replacement for around $20. Any help would be great (links, pics, Etc.) to help me reference. As far as the center steering link goes I’m probably going to get the RPM...

Hello to all, I have a ECX Boost running a Castle Creations Sidewinder 3 w/ a 5700kV brushless motor. I’m experiencing very bad overheating issues. I can no longer go full throttle without the power cutting in and out. Then the ESC cuts power completely and the only thing that works is steering...

ECX Boost User Manual ECX Boost User Manual Also found on: RCDocuments.com

hey, i have been pretty happy with my ECX Boost so far. some hiccups I have had were mainly the driveshafts, after running and small jumps, the driveshafts would fall out or even snap off. what I'm looking for is if there are any driveshafts that are better then stock for the ECX boost buggy. I...

Building a 2wd Torment club racer, and I am also builder a 2wd Torment basher over the winter months here. I have the stock Spectrum DX2E remote and stock receiver whatever number that is. Looking to upgrade to the next level remote for my racer, what is everyone running? I was looking at the...

I am attempting to make a carbon fiber chassis for my Boost. This is 8 layers of carbon fiber hopefully it weighs less and is stiffer than the stock chassis.

I was strolling through my LHS and he had a lone Boost on the shelf marked down to $100. So I got it on a whim thinking it was the same as the Amp DB. Well, it's close. Then I had it in the yard playing with my kids and their Amp MTs it acted like it was overheat protecting itself. So I parked...

Post your favorite Mod

my boost was sloppy in the steering dept, so I ordered a metal steering system off ebay for $30, yes it was high, but man it took care of the problem. no more sloppy steering.. I also upgraded the servo with hitech one!

you can upgrade the driveshafts with traxxas rustler ones, but you will have to shave em down a bit to get them to fit via dremel toll.. so far so good. they are holding up

kinda sucks I recently bought a boost and now its discontinued!!

Hey all! I just installed a 17.5t brushless motor (for stock racing) and I need to change the spur gear on my ECX Boost to something smaller (69-72 teeth). Does anyone know what other brands would work as a direct replacement (or with a minimum of drilling) for the stock ECX 87t spur? Thanks...

I've spent the last few weeks on a (fool's) quest to prep my Boost buggy into a race-capable vehicle. One major sticking point is the front suspension: The Boost's front suspension set-up is a TRUCK set-up. Not for a buggy! The main problem is that with the shorter suspension arms the front...

The link on the ECX site is a dead end and Horizon Hobbies website says it's discontinued. I was thinking of getting one for my nephew for his birthday. Has the AMP desert buggy replaced it?

As part of my recent make-over binge, I purchased a T-Bone Racing "Racer2" bumper for my Boost. The Racer2 bumper is made of a relatively thin (.093" thick) nylon material which keeps weight down and makes for a nice, springy bumper. It is a little wider than the stock bumper (which is the same...

As part of my quest to create a Boost that's not just race-ready, but race-worthy, I've begun a series of upgrades featuring RPM's excellent after-market replacement parts. First up is the "RPM Servo Saver Eliminator Bellcrank." The set ships with Delrin bushings that are a good, close fit and...

Has anyone installed a 12t pinion gear, specifically on a Amp or Boost ? Ive slid the motor over as closest I can but it still ways away from the spur. Even a 15t pinion doesn't set right, barely catches. Are there different types 48p 3mm pinions ?